Tools
IP Configuration
Network Devices
Switch Management
Routing
100
What tool should you use to extend network services beyond demarc?
What is a Punchdown tool
100
Which three of the following are Class B addresses?
What is 129.0.0.0 190.65.2.0 132.12.0.0
100
Which network component connects a device with the transmission media and allows it to send and receive messages?
What is Network Interface card
100
You reconfiguring PuTTY to be used to access the CLI of Cisco switch Which of the following configuration values would PuTTY from connection?
What is 4600 baud Flow contro = RTS/CTS
100
What information does the next hop entry in a routing table identify?
What is The first router in the path to the destination network.
200
You are making Ethernet drop cables using Cat5e cable and RJ45 connectors. You need to remove the plastic coating over the cable to expose the individual wires.
What is Cable stripper
200
What is the default subnet mask for the IP address 203.111.3.3?
What is 255.255.255.0
200
What device sends signals from a computer onto a network?
What is Transceiver
200
A router is configured with the login, no password condition for console access. Which of the following statements is true about access via a Telnet or SSH session?
What is Access is denied
200
A router is connected to a network 192.169.1.0/24 and network 192.168.2.0/24. The router is configured to use RIP and has learned of networks 192.168.3.0/24 and 192.168.4.0/24. The router is also configured with a static route of 0.0.0.0 with a mask of 0.0.0.0. The router receives a packet addressed to the network 10.1.0.0/16. What will the router do with the packet.
What is Forward the packet to the next hop router specified by the route network 0.0.0.0
300
Which of the following connector types are used with UTP cables?
What are RJ45 RJ11
300
You manage a server that uses an IP address of 192.168.255.188 with a mask of 255.255.0.0 Which of the following describes the address type?
What is Classless
300
You have a server that has a 100BaseFX network interface card that you need to connect to a switch. The switch only has 100BaseTX switch ports. Which device should you use?
What is Media converter
300
Which command would you use on a switch to enable management from a remote network?
What is IP default-gateway 192.168.10.185
300
Which of the following routing protocols divides the network into areas, with all networks required to have an area 0 (area 0 identifying the backbone area)?
What is OSPF
400
Which of the following is used to terminate individual wires from a 25 pair or 100 pair cable using female RJ-45 ports.
What is Patch panel
400
Which organization is responsible for allocating public IP addresses?
What is IANA
400
At which OSI model layer does a media converter operate?
What is Layer 1
400
What does the ip address dhcp command all you to do?
What is Configures the switch to obtain an IP address from a DHCP server
400
Which of the following routing protocols is classified as a balance hybrid routing protocol?
What is EIGRP
500
You have a network that occupies both floors of a building. The WAN service provider has installed the line for the WAN service into the building in a wiring closet on the main floor. You have a second wiring closet on the second floor directly above the wiring closet that directly above the wiring closet that holds the demarc. Which of the following terms describes the closet on the second floor?
What is IDF
500
You have a small network connected to the Internet as shown in the Exhibit. You need to configure the default gateway address on Wrk1 so that it can communicate with the hosts on the Internet. Which address would you use for the default gateway address?
What is The IP address assigned to Fa0/0 on Router 1
500
What type of module might a switch use to allow it to modify the media type supported by a switch port? (Select two)
What is SFP GBIC
500
You are configuring a switch so that you can manage it via PuTTY from the same network segment as the switch. On the switch, you enter the following commands. Switch# config terminal switch(config)#interface Evian 1 switch(config-if)#ip- address 192.168.1.10 225.225.225.0 will this configuration work?
What is No, the no shutdown command needs to be entered
500
Which of the following routing protocols are classified as link state routing protocols? select two
What is OSPF IS-IS
M
e
n
u