OSHA
The ________________ gives workers the right to seek safe and healthful
conditions on the job without being disciplined or fired.
A. The Civil Rights Act
B. The Occupational Illness Act
C. The OSHA Act
D. The Labor Relations Act
The OSHA Act
A _______ plan must be available, practiced, and communicated to workers through training when workers are assigned to work at heights.
A. Specific Action Plan
B. Action and Recovery Plan
C. Rescue Plan
D. All of the above
D. All of the above
Users must _________ fall protection equipment before ________ use.
A. Inspect, First
B. Inspect, Each
C. Inspect, Weekly
D. None of the above
B. Inspect, Each
Anchor points for PFA Systems must be in place before you start work, they must
be independent of any platform anchorage and must be able to support at least
__________________ lbs. per worker.
A. 4000
B. 5000
C. 5500
D. 6000
B. 5000
A condition where the risk of electrical shock, arc flash and arc blast is reduced by
de-energizing the circuit or equipment would be classified as an:
A. Primary Condition
B. Secondary Condition
C. Electrically Safe Working Condition
D. Electrically Primary Condition
D. Electrically Primary Condition
_________ serve as a tool for workers to use when determining the hazardous properties of a chemical.
A. Material Safety Data Sheets
B. Newspaper
C. Material Safety Reference Sheets
D. None of the above
A. Material Safety Data Sheets
When sloping from a trench box, the soil line must be below the top of the trench box at least ____.
A. 12”
B. 14”
C. 16”
D. 18”
D. 18”
One who can recognize or identify hazards in the workplace and has the ability and
authority to take the appropriate actions against these hazards would be best
described as a _____________________________.
A. OSHA Compliance Officer
B. Laborer
C. Competent Person
D. Subcontractor
Competent Person
This information can be used to determine restrictions and limitations of fall protection equipment.
A. Manufacturer’s Consequential Data
B. Manufacturer’s Technical Data
C. Manufacturer’s Skill Data
D. None of the above
B. Manufacturer’s Technical Data
If a worker on a scaffold can fall ____ feet or more, they must be
protected by guardrails or PFAS (R&M Policy.)
A. 6
B. 10
C. 12
D. 15
A. 6
Employees have a “ ________________________” what hazardous chemicals or
materials they are working with on the job and how to protect themselves from
the hazards associated with the use of these.
A. Reasonable Cause
B. Right to Act
C. Right to Know
D. Reasonable Doubt
C. Right to Know
_________________ must be used by employees when all methods of trying to
engineer out or eliminate hazards have not been successful. This is commonly
referred as the last level of control.
A. P.P.E.
B. Complaint Forms
C. Disciplinary Forms
D. None of the Above
A. P.P.E.
An excavation of 4’-10” would require what type of protective system?
A. Nothing because the excavation is less than 5 feet
B. Sloping at an angle of 1 ½ to 1
C. Protective systems are not required however the competent person must determine if they are required at less than 5’
D. None of the above
C. Protective systems are not required however the competent person must determine if they are required at less than 5’
What is an effective way of ensuring workers know the contents of containers?
A. Labels
B. Sharpie
C. Training
D. Both A and C
D. Both A and C
All power tools with blades or other moving parts must have ___________.
A. Safety switches
B. Guards
C. Double Insulated
D. Both A & B
D. Both A & B
Section 5 (a)(1) of the OSH Act states that “ Each employer shall furnish to his
employees a place free from recognized hazards that are causing or likely to cause
death or serious physical harm to his employees.” This statement is called the
___________________________________.
A. OSHA Clause
B. General Duty Clause
C. General Safety Clause
D. Employee Right’s Clause
B. General Duty Clause
If ground fault protected, the GFCI can shut off electricity in _________ of a
second.
A. 1/60
B. 1/40
C. 1/20
D. 1/10
D. 1/10
A _____________ is used to identify a chemical or material and its properties,
components, usage methods, etc.
A. Product Data Sheet
B. Product Safety and Health Sheet
C. Safety Data Sheet
D. Material Safety Health Sheet
C. Safety Data Sheet
A Focused Inspection done by OSHA would involve what 4 areas?
A. Falls, Scaffolds, Electrical, HAZCOM
B. Falls, Electrical, Struck-By, Caught-In-Between
C. Falls, Electrical, Fire Protection, Scaffolds
D. None of the Above
Falls, Electrical, Struck-By, Caught-In-Between
A horizontal lifeline system must be installed by a ___________ Person.
A. Competent
B. Knowledgeable
C. Qualified
D. Either of the above
C. Qualified
A scaffold can best be described as a __________________________.
A. Aerial Work Space
B. Elevated Work Platform
C. Lift
D. Hazardous Location
Elevated Work Platform
Fire extinguishers must be ___________ posted so that a fire extinguisher is available for every _______ft² with no more than ______ feet of travel to one.
Evenly, 2000, 200
Conspicuously, 3000, 150
Conspicuously, 3000, 100
None of the above
C. Conspicuously, 3000, 100
Top rails of handrails must be able to withstand at least ________lbs. of force
down and out and mid rails must be able to withstand ________ lbs. of force
down and out.
A. 300, 250
B. 250, 200
C. 200, 150
D. 150, 100
C. 200, 150
Which of the following is not an OSHA injury/illness form?
A. OSHA 300 Log
B. OSHA 301 Form
C. OSHA 301 Injury Log
D. OSHA 300 A Summary
C. OSHA 301 Injury Log
The goal of focused inspections is to:
A. Enforce OSHA’s new policies
B. Look for all hazards on the jobsite
C. Target one specific industry
D. Reduce injuries and illnesses with companies that do not have effective safety and health programs
B. Look for all hazards on the jobsite