O-LEVEL
What work center in an O-level maintenance command is responsible for establishing delivery and pickup points for the material that is ordered, and ensuring that the material that is received is promptly routed to the applicable work center?
Material Control
What level of maintenance is performed in centrally located facilities for the support of operating activities within a designated geographical area, at a particular base or station, or aboard aviation ships?
I-LEVEL
Who is the sponsor of the NAMP?
Chief of Naval Operations
What publication contains the policies and procedures that govern the Technical Directive system?
NAVAIR 00-25-300
What is the primary means that is used to identify a naval message?
Date-time-group (DTG)
What division maintains a master maintenance message board?
Maintenance Administration
What system governs the maintenance actions for intermediate level activity?
NALCOMIS
Who is responsible for the implementation of the NAMP?
Naval Air Force Commander (COMNAVAIRFOR)
What is the TD code for an avionics bulletin (AVB)?
55
What type of school provides basic job entry-level knowledge and skills?
"A"
Maintenance administration shall maintain correspondence per what manual.
SECNAV M-5210.2(series)
Which divisional work center is responsible for the maintenance and upkeep of M197's.
71B
What chapter of the NAMP COMNAVAIRFORINST 4790.2(series) has Maintenance Concepts, Programs, and Processes; Maintenance Unit Department; Division Organization; Manpower Management; and Aviation Officers?
3
What TD priority is assigned to document configuration changes that have been incorporated in all affected equipment by the change designer/ originator before TD is issued?
Record Purpose
what term best describes the following statement: consist of personnel performing maintenance task, by demonstrating and simulation, under the supervision of designated, qualified personnel?
On the job training (OJT)
Name all 7 maintenance work centers within an O-LEVEL command?
13a 110 120 210 220 230 310
Divisional work center 62C/D is responsible for the maintenance and upkeep of what components?
Aircraft Batteries
What does action taken code: K mean? and what purpose is it used?
Calibrated - Adjustment Required.
This code is used when an item must be adjusted to meet calibration standards. If the item needs repair in addition to calibration and adjustment, use another code indicating the proper maintenance action.
How many parts is the ELMS main menu sub-divided into?
4
What publication contains scheduled or forced removal items and their replacement intervals, record of applicable technical directives, maintenance requirement system index by system, and a conditional inspection listing?
Periodic Maintenance Information Card (PMIC)
When would it be applicable to perform a rebase on a special inspection
A special inspection performed earlier than the applicable minus three days or 10 percent limit.
What does Broad Arrow related impact code: C4 mean?
C4: No capability to provide repair/calibration/service.
1 of 1 bench/test set/OTPS/rolling stock non RFU with no workaround.
1 of 2 bench/test set/OTPS/rolling stock RFU, but EXREPs cannot be cleared in a timely manner.
What are some duties and responsibilities of a work center supervisor? name three?
a. Manage workload per the priorities established by Maintenance Control (O-level) or Production Control (I-level). Additionally, IMA Work Center Supervisors will review BMT reports throughout the day to monitor accomplishment of workload priorities.
b. Keep Maintenance Control/Production Control current on workload status (In Work, AWM, AWP, etc.).
c. Immediately inform Maintenance/Production Control of any parts, equipment or personnel problems that prevent accomplishing workload priorities.
d. Direct and supervise work center personnel.
e. Assign trainees to work under the direct supervision of qualified personnel.
f. Periodically monitor work-in-progress to verify compliance with NAMP requirements.
g. Maintain custody and accountability of tools, equipment and facilities.
h. Keep assigned work center, hangar, and flight line spaces clean.
What form is used to initiate a one-time (supply action) request for NAVAIRSYSCOM TM's, TDs, and departmental directives?
DD 1348
What command is responsible for defining and enforcing all policies relative to the creation, storage, and distribution of digital technical data?
Naval Air Technical and Engineering Service Center (NATEC)