Power Tools
Hand Tools
Safety
Handsaws
Hammers
Lumber/wood
Measurement
100
This is a small, tool used to do a task or job that could not be done with the bare hand or without the tool.
What is a Power Tool?
100
This name of this hand tool.
What is a plane?
100
Keep all work surfaces free of ________.
What is clutter/debris?
100
Because sawing creates dust, it is important to wear this when sawing(not safety glasses).
What is particle mask?
100
When connecting two pieces of lumber, use this to hold one of the pieces of lumber (not a C-clamp)
What is vise?
100
This is a place on a piece of lumber where a branch was attached to the tree.
What is the “Knot”?
100
The measure to the nearest 16th of an inch.
What is 7 7/16" ?
200
A power tool with a round blade used for cutting wood and other materials.
What is a Circular Saw?
200
Crescent shaped tool, which can be used to loosen or tighten a nut or bolt. It has a "jaw" (the part where the nut or bolt fits), which "moves"
What is an Adjustable Wrench?
200
This part of the handsaw (not blade).
What is the heel?
200
This part of the hammer.
What is the poll?
200
A general term for a type of wood that is a popular choice for cabinet or furniture making.
What is hardwood ?
200
The measure of the edge of a piece of lumber.
What is thickness?
300
A power tool used to remove rough edges and to smooth and shape materials (not a wood sander).
What is a grinder?
300
A tool used for driving when there is concern for damaging the material.
What is a “Rubber Mallet”?
300
When pulling nails from a piece of lumber, use a _____________under the head of the hammer. This will give you better leverage and also help avoid damaging the piece of lumber.
What is a block of wood?
300
This part of the handsaw (not blade).
What is the toe?
300
This part of the hammer (underneath the claw).
What is the check?
300
This is the cut-off edge of the board.
What is the “End” ?
300
This type of square.
What is a speed square?
400
A power tool with a short flat blade at the end of the saw that moves back and forth to quickly cut wood and other materials.
What is a Reciprocating Saw?
400
What kind of wrench is this?
What is a “combination wrench”?
400
If your saw binds and catches, check the ______________. It may need to be adjusted.
What is angle you’re holding the saw ?
400
The hand saw that makes a cut parallel with the grain of the wood.
What is rip saw?
400
This type of hammer.
What is ball peen?
400
This is the side of the board.
What is “Edge”?
400
A measuring tool should be marked every ____ inch.
What is 1/4 " ?
500
A power tool with the blade located underneath the saw body used to cut circles, curves, and holes in wood and other materials(another name for jig saw)
What is a “sabre saw”?
500
A tool used to make sure a surface is flat (horizontal).
What is a level?
500
The hand saw that makes a cut against the grain of the wood.
What is crosscut saw?
500
When nailing into hardwood, rub the nail with beeswax, paraffin, or dish soap before starting to make the nail drive more easily. You can also do this before driving the nail to help get the nail started.
What is drill a small hole into the wood?
500
Softwoods don’t have this.
What are pores?
500
Most tape measures will be marked in increments of 1/8", 1/16", and this, making them more precise.
What is 1/32" ?
600
A woodworking tool used to test and mark proper angles, draw lines for making straight cuts, and other things (is not triangular in shape).
What is the combination square?
600
Woodworking can create large amounts of dust so good __________________ is necessary in the work area.
What is ventilation?
600
Which type of saw has few teeth that appear like a series of chisels placed in a row and is held at a 60 degree angle to the wood?
What is rip saw?
600
The slit in the wood made from a saw blade
What is KERF?
600
This type of square.
What is framing square?