Fundamentals of Electricity and Electronics
Physics & Engineering
Ground Ops & Servicing
Mechanic Certification, Privileges, & Limitations
Materials & Processing
Cleaning & Corrosion Control
100

The purpose of providing a space underneath the plates in a lead acid battery's cell container is to

prevent sediment buildup from contacting the plates and causing a short circuit.

100

A wing with a very high aspect ratio (in comparison with a low aspect ratio wing) will have

a low stall speed.

100

If a radial engine has been shut down for more than 30 minutes, the propeller should be rotated through at least two revolutions to

check for hydraulic lock.

100

 What is the maximum duration of a temporary mechanic certificate?

120 days

100

If dye penetrant inspection indications are not sharp and clear, the most probable cause is that the part

was not thoroughly washed before the developer was applied.

100

How may magnesium engine parts be cleaned?

Wash with a commercial solvent, decarbonize, and scrape or grit blast.

200

Typical application for zener diodes is as

voltage regulators.

200

The speed of sound in the atmosphere

changes with a change in temperature.

200

How are aviation fuels which possess greater antiknock qualities than 100 octane, classified?


By performance numbers.

200

Under the Federal Aviation Regulations, an aviation maintenance technician is required to perform maintenance on an aircraft so that it

is at least equal to its original or properly altered condition

200

One of the main advantages of Hi-Lok type fasteners over earlier generations is that



they can be installed with ordinary hand tools.

200

What may be used to remove corrosion from highly stressed steel surfaces?

Fine grit aluminum oxide.

300

A thermal switch, or thermal protector, as used in an electric motor, is designed to

open the circuit in order to allow cooling of the motor.

300

The purpose of aircraft wing dihedral is to


increase lateral stability.

300

When approaching the front of an idling jet engine, the hazard area extends forward of the engine approximately

25 feet.

300

14 CFR part 65 subpart D contains information for the certification of

mechanics

300

What tool is generally used to set a divider to an exact dimension?

Machinist scale.

300

A correct use for acetone is to


remove grease from fabric.

400

What determines the amount of current which will flow through a battery while it is being charged by a constant voltage source?

The state of charge of the battery.

400

If the temperature of a confined liquid is held constant and its pressure is tripled, the volume will

remain the same.

400

When taxiing an airplane with a quartering tailwind, the elevators and

upwind aileron should be held in the down position.

400

Who may perform the work activities required for a major repair or alteration to an aileron?

Any certified mechanic with an airframe rating, but the work must be signed off for return to service by an IA.

400

A bolt with a single raised dash on the head is classified as an

AN corrosion resistant steel bolt.

400

If masking tape is applied to an aircraft such as for trim spraying, and is left on for several days and/or exposed to heat, it is likely that the tape will

cure to the finish and be very difficult to remove.

500

What schematic symbol represents a current limiter?

Two triangles pointing to each other with a line on both sides of the triangles.

500

Newton's Second Law of Motion, generally termed the, "Law of Momentum", states:

Acceleration is produced when a force acts on a mass. The greater the mass, the greater the amount of force needed.

500

Characteristics of detonation are

rapid rise in cylinder pressure, excessive cylinder head temperature, and a decrease in engine power.

500

The replacement of a damaged engine mount with a new identical engine mount purchased from the aircraft manufacturer is considered a

minor repair.

500

In examining and evaluating a welded joint, a mechanic should be familiar with


likely ambient exposure conditions and intended use of the part, along with type of weld and original part material composition

500

What is likely to occur if hydrated wash primer is applied to unpainted aluminum and then about 30 to 40 minutes later a finish topcoat, when the humidity is low?

A glossy, blush-free finish.

600

In an AC circuit, the effective voltage is

less than the maximum instantaneous voltage.

600

If two actuating cylinders which have the same cross sectional area but different lengths of stroke are connected to the same source of hydraulic pressure, they will exert


equal amounts of force and will move at the same rate of speed.

600

Characteristics of aviation gasoline are

high heat value, high volatility.

600

What is the normal duration of a mechanic certificate with airframe and/or powerplant ratings?

Until surrendered, suspended, or revoked.

600

When a mechanical force is repeatedly applied to most metals at room temperature, such as rolling, hammering, or bending, the metals become

cold worked, strain or work hardened

600

What type of corrosion may attack the grain boundaries of aluminum alloys when the heat treatment process has been improperly accomplished?


Intergranular

M
e
n
u