GSM Advancement Study

Eng Controls

100

True or False. A normal stop on a GTE can be initiated by the PCC operator in either the programmed control mode or the manual control mode.

True

200

on the DD-963 class ships, what are the two main air systems associated with the GTEs and GTGSs? A.) Bleed air and Ship's service Air B.) Bleed air and HP air C.) Ships service air and HP air D.) Emergency air and HP air

Bleed Air and HP air

300

What total number of the nine automatic GTE shutdowns can be inhibited by placing battle override on ? A.) Five B.) Seven C.) Eight D.)Nine

Five

400

Which of the following classes of gas turbine-powered ships uses the machinery control system (MCS) to control and monitor its gas turbine equipment? A.) DD-963 B.) DDG-993 C.) DDG-51 D.) FFG-7

DDG-51

500

The MRG contains a total of how many (a) gearbox bearing and (b) line shaft bearings? A.) (a) 1; (b) 28 B.) (a) 1; (b) 29 C.) (a) 28; (b) 1 D.) (a) 29; (b) 1

(a) 28; (b) 1

Engineering Admin

100

At what interval does the CO receive a fuel and water report? A.) Monthly B.) Weekly C.) Daily D.) Hourly

Daily

200

What type of FBR is required to be sent by naval message? A.) Priority B.) Special C.) Strategic D.) Urgent

Urgent

300

Category A on an FBR is Used for all the following reasons EXCEPT which one? A.) To order new maintenance index pages. B.) To order new maintenance requirement cards. C.) To discuss matters of a nontechnical nature. D.) To report procedural discrepancies

To report procedural discrepancies

400

While Preforming PMS on a piece of equipment, you notice a specific tool is required that is not listed on the PMS card. What category block on the PMS FBR should you use to indicate this discrepancy? A.) A B.) B C.) Either 1 or 2 above, depending on the discrepancy D.) C

B

500

What QA level provides the least amount of quality control? A.) A B.) B C.) C D.) D

D

Power Train

100

How are the stern tube and strut bearings cooled? A.) By heat-dissipating fins B.) By air from the masker air system C.) By fresh Water D.) By Seawater

Seawater

200

The Electronic pitch position transducer is located in what area? A.) Inside the CRP electronics enclosure B.) On the right side of the OD box C.) on the front end of the OD box D.) Inside the Propeller hub

Inside the Propeller hub

300

When pinion and gear teeth have been slightly indented by foreign material, what action should you take? A.) Closely Monitor the damage to see if it spreads B.) Remove both gears for a complete overhaul C.) Remove the raised metal on the damaged teeth D.) Remove the raised metal on both gears

Remove the raised metal on the damaged teeth.

400

A steady increase in hub servopressure, without a change in system demands, is a good indication that which system components is faulty? A.) Auxiliary relief valve B.) sequencing valve (closed position) C.) Reducing valve D.) Electrohydraulic servo valve

Electrohydraulic servo valve

500

When preforming a static check to determine tooth contact, you should use which of the following compounds to coat the gear teeth? A.) An indelible marker B.) Copper sulfate C.) Persian blue D.) Prussian blue

Prussian Blue

Oil Lab

100

The API gravity conversion charts for F-76 fuel can be found in what chapter of the Naval Ships Technical Manual? A.) Chapter 223 B.) Chapter 234 C.) Chapter 541 D.) Chapter 542

Chapter 541

200

A diesel LO acidity test must be performed on an idle diesel at what minimum periodicity? A.) Daily B.) Weekly C.) Biweekly D.) Monthly

Weekly

300

To allow the water to circulate and the boiler to stabilize, you should wait a minimum of how many seconds between blowdown cycles? A.) 30 seconds B.) 45 seconds C.) 60 seconds D.) 90 seconds

60 seconds

400

What is the maximum amount of TSP that can be injected into a boiler at one time? A.) 200 grams B.) 300 grams C.) 400 Grams D.) 500 grams

500 grams

500

If a chemical chloride test result is less than the salinity indicator reading by more than 0.02 epm, what action(s), if and, should you take next? A.) Perform a hardness test B.) perform another chloride test C.) Secure and dump the boiler D.) None

Perform a hardness test

Gas Turbine Maintenance

100

When should the replacement engine containers be brought to the site? A.) after the old engine has been removed B.) After supply had been inventoried the containers C.) As the new engine is needed D.) As soon as possible

As soon as possible

200

To maintain better control over the rotor speed when jacking the engine you should use which of the following tools? A.) A torque multiplexer B.) A Torque Multiplier C.) An electric drive motor D.) An air Drive Motor

A torque multiplier

300

When you are inspecting the combustion section of a GTE, what wattage light source should you use? A.) 1,000 B.) 750 C.) 500 D.) 250

1,000

400

Active corrosion on copper alloys is indicated by which of the following conditions? A.) A verdigris formation B.) a white gray powder formation C.) A gray-green patina formation D.) A copper-oxide crust formation

A gray-green patina formation

500

Tip Clang can be attributed to which of the following operating conditions? A.) Overloading B.) Compressor stall C.) Continuous low -power operation D.) Continuous High-power operation

Compressor stall