Multi-view Drawings
In Europe, drawings use first-angle projection. This method is preferred by which standards organization?
A - ASTM
B - ANSI
C - ISO
D - SME
C - ISO
Ensuring policies and procedures are being followed, customer requirements are met, and identifying opportunities for improvement are goals of a(n) __________.
A - In-line product inspection
B - Employee orientation
C - Quality audit
D - Frequency report
C - Quality audit
All employees in the plant benefit when __________.
A - Data on a specific employee's performance is collected and analyzed
B - Engineers keep their distance from hourly personnel
C - Operators can choose what hours they work
D - Defect trend data is collected and problems are corrected
D - Defect trend data is collected and problems are corrected
When is production stopped?
A - When critical problems are found
B - When non-critical problems are found
C - When both critical and non-critical problems are found
D - Production is never stopped
A - When critical problems are found
What is the most basic SI to US customary unit conversion?
A - Millimeters to inches
B - Meters to inches
C - Kilograms to pounds
D - Grams to pounds
A - Millimeters to inches
If a drawing shows the right side view to the left of the front view, does that drawing use first or third-angle projection?
A - First
B - Third
A- First
To perform an end-item inspection of a product is a type of __________.
A - Safety audit
B - Training report
C - Tool calibration
D - Quality assurance audit
D - Quality assurance audit
Control charts are used to determine __________.
A - The amount of rework required
B - The process capability
C - The machine cycle time
D - Worker's vacation time
B - The process capability
What action eliminates the cause of nonconforming parts?
A - Preventative action
B - Corrective action
C - Eliminating action
D - Conforming action
B - Corrective action
What must be done to convert feet to millimeters?
A - Convert feet to inches, then convert the inches to millimeters
B - Convert feet to meters, then convert the meters to millimeters
C - Multiply the number of feet by 25.4
D - Feet cannot be converted into millimeters
A - Convert feet to inches, then convert the inches to millimeters
Which type of projection method is typically used in the United States?
A - First Angle
B - Second Angle
C - Third Angle
D - Right angle
C - Third Angle
Parts are inspected __________ to make sure the typical characteristics of produced parts are found.
A - In small lots
B - In large lots
C - At only one time each shift
D - Randomly
D - Randomly
What often happens if operators adjust recently produced parts based on recent measurements?
A - Part variation will decrease
B - Part variation will increase
C - More parts will be processed
D - There will be no change
B - Part variation will increase
Troubleshooting is finding the cause of a production problem. After stating the problem, what is the next step in the troubleshooting process?
A - Write out the problem
B - Identify possible causes
C - Evaluate corrective actions
D - Collect information about the problem
D - Collect information about the problem
To convert from inches to millimeters, multiply the inches by __________.
A - 2.5
B - 0.612
C - 25.4
D - 1.6
C - 25.4
Which of the following has the primary purpose of showing internal detail?
A - Orthogonal view
B - Auxiliary view
C - Sectional view
D - Multiview
C - Sectional view
One hundred percent inspection may be required for certain __________ products.
A - Low cost, high volume
B - High cost, low volume
C - Highly Capable
D - Low defect
B - High cost, low volume
How is an unstable (out-of-control) process defined, and what should be the response?
A - In an unstable process, the mean of the measurements is outside the control limits of the process. The process should be investigated
B - In an unstable process, the mean of the measurements is within the established control limits with only natural causes of variation. No investigation is needed
C - In an unstable process, a process is producing parts faster than expected. No investigation is needed
D - In an unstable process, a process is producing parts faster than expected. It should be monitored closely to see if the next sample will fall outside the control limits
A - In an unstable process, the mean of the measurements is outside the control limits of the process. The process should be investigated
A Corrective Action Report was submitted to prevent the use of the wrong foam in a packaging process. This has been a recurring problem. The normal audit time in this department is usually every six months. What should be done in this situation?
A - The foam should be checked every time it is replenished and documented
B - The audit time should be cut in half to every three months
C - The specifications should be rewritten so that any type of foam can be used
D - The audit time should be changed to weekly
A - The foam should be checked every time it is replenished and documented
10 inches is the same length as __________ mm.
A - .254
B - 2.54
C - 25.4
D - 254
D - 254
What is a view projected from a primary auxiliary view called?
(Answer should be in a short sentence)
- Secondary auxiliary view
Everyone involved with a quality check __________.?
(Answer should be a short sentence)
- Should see the collected data
Control charts provide __________ to allow manufacturers to analyze problems on a piece of equipment.?
(Answer should be a short sentence)
Historical Data
What is the next step in response to a quality error?
(Answer should be a short sentence)
- Follow the approved quality plan
If a box of parts weighs 27.3 kilograms, how many pounds does it weigh?
(Answer should be in "Number of lbs" for example
"42 lbs" )
- 60 lbs