Bert
"The Basher"
"The Basher"
Danger signs shall be used only where:
a. There is a scaffold
b. An immediate hazard exists
c. Other trades must be kept out of an area
d. A competent person thinks they are necessary
b. An immediate hazard exists
Which soil type has sandy clay loam, with an unconfined compressive strength of 1.2 TSF?
a. A
b. B
c. C
d. C modified
b. B
A material chute used during demolition operations must be enclosed when its angle is equal to or greater than ____ degrees:
a. 35
b. 45
c. 55
d. 65
b. 45
The __________ must have authority to stop and refuse to handle crane loads until a qualified person has determined the load is safe to lift.
a. Lead rigger
b. Crane operator
c. Competent person
d. Site superintendent
b. Crane operator
Clearances between the top level of stored materials and sprinkler head deflectors shall be at least _____ inches:
a. 26
b. 30
c. 36
d. 40
c. 36
All hand and power tools shall be:
a. Tested monthly
b. Equipped with safety guards
c. Maintained in a safe condition
d. Kept in an approved storage container
c. Maintained in a safe condition
An employee is observed cutting lumber with a circular saw that has a damaged electrical cord. The appropriate action is to have the circular saw tagged and ____.
a. Continue to use
b. Replace the plug
c. Repair the cord with electrical tape
d. Taken out of service
d. Taken out of service
Who is required to ensure that electrical equipment is free from recognized hazards that are likely to cause death or serious physical harm?
a. Employee
b. Employer
c. OSHA
d. Union
b. Employer
In the absence of an infirmary, clinic, hospital, or doctor that is reasonably accessible in terms of time and distance from the worksite, the employer shall make sure a _______________ is available at the worksite.
a. Licensed health care provider
b. Supply of hydrogen peroxide
c. Person with a valid first aid training certificate
d. Means of transporting the injured employee
c. Person with a valid first aid training certificate
The ____________ is responsible for the approval of a powered industrial truck’s attachments or modifications.
a. Employer
b. Mechanic
c. Manufacturer
d. Operator
c. Manufacturer
If a Rollover Protective Structure (ROPS) is removed for any reason, it shall be remounted with:
a. Attached by any welding method
b. Equal or better bolts as required for the original mounting
c. Nothing; the ROPS can remain dismounted and remounting is not required
d. Remounted with any fasteners available at the jobsite
b. Equal or better bolts as required for the original mounting
The results of workplace injuries and illnesses may include:
a. Reductions in DART and incidence rates
b. Improved customer relations and fewer schedule delays
c. Lower morale and increased costs to train replacement worker
d. Lower workers’ compensation costs and less employee turnover
c. Lower morale and increased costs to train replacement worker
The statement “Protecting the safety and health of America's workers is an important factor in reducing worker fatalities, injuries, and illnesses” is found in:
a. CFR 1904
b. CFR 1926 Subpart C
c. Section 1 of the Occupational Safety and Health Act
d. Section 5(a)(1) of the Occupational Safety and Health Act
c. Section 1 of the Occupational Safety and Health Act
The side rails of a portable ladder must extend at least ____ feet above the landing surface:
a. 2
b. 3
c. 4
d. 5
b. 3
Section 5 of the OSH Act is also known as:
a. The Anti-retaliation clause
b. The "me too" clause
c. The general duty clause
d. Santa clause
c. The general duty clause
What is the minimum separation from overhead power lines up to 50KV?
a. 5 ft
b. 10 ft
c. 15 ft
d. 20 ft
b. 10 ft
The top inspection priority for OSHA is:
a. fatality
b. complaints
c. imminent danger
d. follow up
c. imminent danger
In addition to daily inspections, cranes must also have documented inspections:
a. weekly and monthly
b. biweekly
c. monthly and annually
d. semi-annually
c. monthly and annually
According to 29 CFR 1926 Subpart M, the top rail of a guardrail system must be at:
a. 42 in +/- 3 in
b. 39 in +/- 3 in
c. 36 in +/- 6 in
d. 45 in +/- 6 in
a. 42 in +/- 3 in
Power tool such as a hand held circular saw must be equipped with:
a. constant pressure light
b. constant pressure gauge
c. constant pressure coupler
d. constant pressure switch
d. constant pressure switch