PPE
Knowledge
Stairs/Ladder
Don't Die
Random
Fire Protection & Prevention
Surprise
100
___________ is the first step in the hierarchy of controls, while ___________ is the last.
Elimination and PPE
100
How often do scaffolds need to be inspected?
Daily
100
The ______ _______ steps of a ladder are restricted from being utilized.
Top Two?
100
A confined space is defined as a space large enough for entry, limited means of egress, and a space ___________________.
"Not intended for continuous occupancy?
100
The item that states a chemical, health hazards associated with that chemical, the PPE requirement when handling a chemical and has pictograms is called a ____________.
Safety Data Sheet?
100
This employee may initial the monthly inspection of any fire extinguisher.
Any trained employee
/operator
100
What does JSA stand for?
Job Safety Analysis.
200
This is how often PPE should be inspected!
Before Each Use
200
I will follow proper _________ procedures whenever servicing or maintaining machines or systems in which the unexpected energization, start-up or release of stored energy could cause injury.
Lockout/Tagout
200
A straight ladder must extended _______ feet above the landing.
3 feet?
200
The acceptable oxygen level is between _____________.
19.5% and 23.5%?
200
Which term describes a tool that is powered by compressed air?
Pneumatic tools
200
After “Tagging” a bad fire extinguisher out of service, what must you do?
Remove it from site
200
Top rails must withstand ___ pounds of downward and outward force?
200
300
This is the height at which fall protection is required in the construction industry.
6 feet
300
What does GFCI stand for?
Ground-Fault Circuit Interrupters
300
Ladders should be set up with a ______ to ______ ratio.
4 to 1
300
Three elements needed to cause a fire are ____________, _______ & _________.
Heat, oxygen, and fuel?
300
What's wrong with this Ladder?
What's wrong with this Ladder?
Missing Ladder Labels
300
This employee is implemented to ensure the fire-safety of a building or situation that may pose an increased risk to persons or property.
Fire Watch
300
Prior to wearing a respirator a worker must have __________.
FIT test
400
This is the ANSI cut level that all gloves must meet according to CWC.
Cut level 4
400
What does a yellow tag on a scaffold mean?
Yellow means use caution and you must wear fall protection while on the scaffold.
400
Staircase landings must have a __________ around the open edge.
A guardrail system?
400
Compressed gases are considered stored properly when the regulator is removed and ____________ are placed on.
Caps?
400
Guardrails are often used by employers to protect workers from falls. How high must the top guardrail (the top rail) be above the working surface
42 inches, plus or minus 3 inches
400
This acronym is commonly used to remind employees how to use a fire extinguisher.
P.A.S.S.
400
This symbol refers to this type of fire.
Flammable Liquids
500
Anchor points must withstand ______ pounds?
5,000
500
Scaffolds can only be erected, moved, dismantled or altered under the supervision of a ____________?
Competent person
500
Handrails must be free of ___________.
Defects and puncture hazards.
500
The three roles played in a confined space operation are the ____,___, and _________.
Attendant, Entrant, and Entry Supervisor?
500
I will not bodily enter one of these without first contacting safety personnel. I will not enter THIS unless I have been properly trained and have the proper equipment.
Confined Space
500
This document is required when a source of ignition or flammable material is present or can be a fire hazard regardless of the presence of flammable material in the workplace. Common processes are:
welding, soldering, cutting and brazing.
Hot Work Permit
500
This is the amount of weight a hole cover must be able to support?
2 times the working load
