UG / OH
WHAT DEVICE IS UTILIZED WHEN GROUNDING A CUT-OUT FOR UG RISER?
CUT-OUT GROUNDING CLAMP (GROUNDING STIRRUP).
WHEN READING A ONE LINE WHAT SIGNIFIES A NORMAL OPEN POINT.
SWITCH OR DX'S HIGHLIGTHED IN YELLOW.
TRUE OR FALSE. WHEN ISOLATING PRIMARY URD LAYING IN THE BOTTOM OF THE PAD IS BEST PRACTICE.
FALSE.
CABLES SHOULD BE STOOD OFF ON FEED THROUGH AND CAPPED OR GROUNDED.
PER EO-1010: HOW OFTEN SHOULD THE ROPE ON THE PULLER/TENSIONER BE VISUALLY INSPECTED?
Upon paying out the rope on the puller tensioner unit, a visual inspection of the entire line must be completed, to ensure there are no abrasions, damage spots, or issues with the portion of the rope that will be utilized for the pull.
I'M A NH NATIVE OLD MAN, I HAVE FALLEN AND CAN'T GET UP
THE OLD MAN OF THE MOUNTAIN
A 1200 AMP SERVICE REQUIRES HOW MANY RUNS OF WHAT SIZE WIRE?
4 RUNS OF 500KCMIL.
A RED MARK UP ON A ONE LINE DRAWING SIGNIFIES WHAT?
RED = FUTURE ADDITION
WHAT IS THE MAXIMUM ALLOWABLE DISTANCE GROUND CLAMPS FOR PERSONAL PROTECTIVE GROUNDS CAN BE APART
3"
INFORMATION FOR THE PRIMARY BYPASS TRAILER CAN BE FOUND IN WHAT PROCEDURE.
EO-1180 PRIMARY BY-PASS TRAILER PROCEDURE.
10
FALSE. LINDSEY SENSORS MUST BE GROUNDED AND CONNECTED PRIOR TO ENERGIZED PHASE BEING LANDED.
338 AND THE 346 HAVE A TIE POINT AT WHAT STATION?
MELVIN VILLAGE
TRUE OR FALSE. THE CORNHOLE SAFETY MANUAL STATES, BAGS PARTICULARLY IF THEY BREAK OPEN DUE TO WEAR AND TEAR, CAN RELEASE POWDER, POSING A CHOKING HAZARD.
FALSE, THERE IS NO SINGLE UNIVERSAL SAFETY MANUAL FOR CORNHOLE, THIS WOULD BE A MANUFACTURE WARNING.
TRUE OR FALSE: PER SH-6012 ALL CUT-OUT AND IN-LINE DISCONNECT THAT ARE EQUIPPED WITH ATTACHED HOOK AND PULL RINGS THAT HAVE NOT BEEN BY-PASSED SHALL BE OPENED WITH A SHOTGUN.
FALSE: All cutouts and in-line disconnects that are equipped with attachment hooks and pull rings that have not been by-passed shall be opened with a load interrupting tool. Exception: When visual openings exist, and no load is present, a load interrupting tool is not required.
OFFICIAL STATE DOG OF NEW HAMPSHIRE? THE NAME ALSO REFERS TO A VARIETY OF SALMON.
CHINOOK
WHAT 3 STEPS NEED TO BE TAKEN WHEN CUTTING A PRIMARY URD.
1) ISOLATE.
2) TEST.
3) GROUND.
ABC WITHIN A RECLOSER SYMBOL SIGNIFIES WHAT ON A ONE-LINE DRAWING?
DISTRIBUITION RECLOSER WITH SINGLE PHASE TRIPPING.
NAME 5 OF THE 7 CO-PILOT EXPECTATIONS.
1. TEAM WITH THE DRIVER TO MAINTAIN SAFE DRIVING.
2. NOT DISTRACT THE DRIVER
3. ATTEND TO ALL NECESSARY TELECOMMUNICATIONS.
4. ASSIST WITH THE PARKINK, BACKING, AND LANE CHANGES.
5. ALERT, BUT NEVER ALARM THE DRIVER.
6. OBSERVE DRIVER APTITIUDE.
7. CO-PILOT FOR SAFETY OF ALL ON THE ROAD.
PER SH-6026 AT WHAT INTERVAL SHALL LIVE LINE TOOLS BE REMOVED FROM SERVICE, TESTED, AND LABLED.
All live line tools used as the primary protection of employees shall be removed from service, tested and labeled with test date every two years. If tools are repaired and/or refinished, they shall be electrically tested before being placed back in service. (SH-6026)
NEW HAMPSHIRE MOTTO LIVE FREE OR DIE IS FOLLOWED WITH WHAT SHORT SENTENCE.
DEATH IS NOT THE WORST OF EVILS.
WHERE WOULD YOU FIND THE REQUIRMENTS TO TEST OPERATE A DEVICE WITHIN A CLEARANCE ZONE.
PERMISSION AND CLEARANCE ISSUE STATEMENT #2.
2. DO YOU FULLY UNDERSTAND THE SCOPE OF THE JOB AND ACKNOWLEDGE THESE LIMITS TO BE ADEQUATE
WHEN THE LINE IS DE-ENERGIZED AND GOING TO WORK HOT WHAT TAG IS NEEDED.
PERMISSION
WHAT IS THE COMPANY SPEED LIMIT INSIDE THE FENCE OF AN AWC? EXCEPT WHICH ONE?
10 MILES PER HOUR, 5 MILES PER HOUR AT LEGENDS
If an electric train is moving north at 100mph and a wind is blowing to the west at 10mph, which way does the smoke blow?
AN ELECTRIC TRAIN HAS NO SMOKE