SEPMS
O-level and I-level activities must maintain an SE Custody and Maintenance History Record (OPNAV 4790/51) per paragraph 8.5.17 for all items of SE that?
In their custody that require depot level maintenance or rework
Immediate Action TDs must be complied with prior to?
The next flight or use of the affected aircraft, engine, or equipment.
MAL CODE 799?
NO DEFECT-malfunction could not be duplicated, item checks good
1. Which maintenance concept divides the total scheduled maintenance requirement into small packages or phases of approximately the same work content?
Phase
Personnel assigned to the CTPL should be retained in the billet for a minimum of how many months?
12
CM ALS is not required for an item of SE which is what?
(Repairable (determined by SM&R code), and does not have PMs beyond Daily and Pre-Op, and does not have any TDs issued against it.
Which category is assigned to TDs when unsafe conditions exist which, if uncorrected, could result in fatal or serious injury to personnel, or extensive damage or destruction of valuable property; and the conditions embody risks calculated to be unacceptable?
Immediate Action
What are the 6 TD status codes?
A Assisting Work Center
C Complied With
D Does Not Apply
P Previously Complied With
Q TD Removal
W Work in Progress
Engines with major inspection intervals of 400 hours or more will have major inspections performed if what percent or less of the interval remains until the next inspection?
25%
a numbering system developed in coordination with other Systems Commands. This change was in response to a Naval Material Command sponsored project for standardizing TM numbers and their method of assignment.
TECHNICAL MANUAL IDENTIFICATION NUMBERING SYSTEM (TMINS)
When an item of SE is new and has never been placed in service or is received after completion of rework by a depot designated repair point (DRP), when is the next PM cycle initiated?
the next PM cycle will be initiated based on the date of completion of the acceptance inspection.
TDs may be amended a maximum of how many times?
3
TD CODE 73
what is Meteorological Equipment Change (MEC)?
What is responsible for the development, expansion, execution, and support of maintenance plans for component repair?
COMNAVAIRSYSCOM
How often must the Depot FRC CTPL or designated representative perform an audit on all DTPL, satellite libraries and Library Service Area (LSA) operations?
Quarterly
(I-level) CM ALS for each AESR must be backed-up when?
Upon RFI. SE CM ALS will be saved after completing a scheduled or unscheduled maintenance action and after making a miscellaneous history entry on the item. All back-ups or saves will be in PDF format on an external media source,
(SE) TDRS NAT02 Report verification procedures:
(1) Download the NAT02 report each month from DECKPLATE (https://deckplate.navair.navy.mil/#/). Select the NAT02 report with Index Codes B & D for “BASELINE” verifications and Index Code B for “SUBSEQUENT” verifications. Compare this report to the previous “SUBSEQUENT” verification and research any differences noted.
(2) Annotate TD status applicability to specific equipment held within the activity. Annotation can either be done electronically or by hard copy.
(3) Maintain a current annotated NAT02 with applicable TDs in the location directed by the TD Compliance Program Manager.
(4) Document performance of NAT02 “BASELINE” verification and annual “SUBSEQUENT” verification on the SE Custody and Maintenance History Record (OPNAV 4790/51) Section VI Miscellaneous History Record and NALCOMIS OOMA CM ALS Miscellaneous section.
(5) File “BASELINE” and “SUBSEQUENT” in the Historical File per 10.17.3.7.
Phase Inspection type Maintenace code
G
What is the title of the overall program which provides the data required for the effective management of SE at all levels of aircraft maintenance?
Aircraft Maintenance Material Readiness List (AMMRL)
The CTPL Manager (O-level and I-level) must incorporate IRACs, Rapid Action Changes (RAC), and Electronic Rapid Action Changes (ERAC) within 2 working days of receipt and incorporate formal changes, routine revisions and notices within how many working days of receipt?
5 days
PM on up to 10 items of the same type of equipment may be documented as a “lot” on one WO or MAF if all of the following conditions are met:
(1)All equipment in the lot must be the same model.
(2)The same PM requirements must apply to the entire lot.
(3) One technician must be able to complete PM for the entire lot in one work shift.
What are all the TDRS reports and lists:
(1) NA500C, Aeronautical TD Index Report, provides a list of active TDs, applicable to each type/model/series (T/M/S) aircraft and engine.
(2) NAT02, SE TD Listing (with index codes B and D), provides information by Type Equipment Code and is used to screen for active and completed Support Equipment (SE) TDs.
(3) NAT04, Aviation Aircrew Equipment TD Listing (with index codes B and D), is used to screen for active and completed Aviation Life Support Systems (ALSS) TDs.
(4) REP07, TD Compliance Report, provides a complete list of incorporated TDs for specific component serial numbers (S/N), used to validate prior incorporations.
(1) LIST01, TD Applicability Listing, provides a quick reference to Airframe Change (AFC) and Airframe Bulletin (AFB) TDs based on applicability range and series information for specific T/M/S aircraft.
(2) LIST02, TD Requirements Listing, provides a list of Not Incorporated (NINC) AFBs and AFCs for individual aircraft, and Power Plant Bulletins (PPB) and Power Plant Changes (PPC) for engines.
3) LIST04, Incorporation (INC) Listing for Equipment, provides a list of Incorporated (INC) AFBs and AFCs for individual aircraft; and PPBs and PPCs for engines.
(4) LIST04H, Historical Incorporation Listing for Equipment, provides a list of historical INC AFBs and AFCs for individual aircraft, and is used to validate prior compliance.
Seat Survival Kit Record
what is form OPNAV 4790/137
How many categories are there in which to declare a strike and what are they?
Category 1 (Damage), Category 2 (Depreciation), Category 3 (Administrative), Category 4 (Completed Service Life)
what is an Initial Outfitting List (IOL)
the IOL function is used to generate a list of all TMs that are associated with a particular platform and maintenance level.