Define FAAD/ C-RAM C2 workstation C2
What two radios are used to transmit data to fire units?
SINCGARS and EPLRS
How are system administration tasks performed by Operator?
Using Co-Host Tools
What are the 4 data cycles that subsystem use for a SINCGARS Network?
6-Sec, 4-Sec, with C2, 4-Sec with relay, 2-Sec
What are the hard coded FAAD ID Numbers?
001-AB, 002-AC, 003-S1, 004-S2, 005-S3, 006-S4, 007-S5, 008-S6
What are the 3 primary network types for internal communications?
LAN, EPLRS, and SINCGARS
Air and battle management data are received from what organic sources?
Sentinel Radar
What is the Data rate setting for the SINCGARS and EPLRS radios, which is applicable to the operations of the FAAD/C-RAM C2?
Data rate setting for the SINCGARS radio is 2400/2400N and EPLRS radio is 32000.
The Operational Screen is divided into 5 areas, what are they?
Title Bar, Control Panel, Navigation Bar, FAAD3D BSD, & Information Bar.
What is the purpose of the built-in diagnostic test?
Checks network connectivity of Communication devices.
What happens to the workstation, when you confirm Exit during restart procedures?
Selecting Exit button immediately restarts FAAD/C-CRAM C2 without warning.
All TP w/Snsr(s) on EPLRS-MSG IntraFAAD share what?
Same air picture, AOI, and alert thresholds.
What are the 3 operating modes and which of those are the typical one used?
Workstation, Server, and Simplified Sense and Warn Sheltered System (SSWSS) Workstation.
What shift change procedure is selected when dealing with Uncleared Personnel?
Shift-F12 (Full Screen)
When SINCGARS radios are used as the primary means of Comms, what must the initial broadcaster in each FAAD network do?
Build a ULT.
If you are performing a complete shutdown of the workstation, when should you remove the CD/DVD from the CD/DVD tray?
Remove CD/DVD before exiting, because the tray will not open after shutdown.
What is deactivated in a SINCGARS Four-Second (2+2) Data Cycle with C2?
HH Relay
Describe the Tactical Communication Interface Module (TCIM)?
Interfaces with Sheltered radios and radar units to transmit and receive secure and non-secure data. TCIM has 2 communication channels, channel 1 & 2.
What is an alerted Air Track?
A track that meets the criteria defined in Track AOI, ID Weights, Alert Thr, & M3 Alerts buttons.
Describe the Hostlog for FAAD C2!
Hostlogs for Own subsystem can be managed using recording options and hostlogs, media files, or playback files for Own or another subsystem can be managed using options to export.
Describe a HARD Reboot on the FAAD/C-RAM C2 workstation!
A hard reboot is a manual and physical restart of the workstation. Only perform this procedure in event of a critical error as it may cause damage to software files.
All__ participants communicate via Link 16 (TADIL-J) message protocols and MIDS radios or JREAP compatible media?
JDN
On the TCIMs, What are port J1/J2 and J4/J9 used for?
J1/J2-SINCGARS and J4/J9-EPLRS/MIDS/Sentinel FDL
What functions are located on the BSD Information Bar?
Operator Feedback, Other Alert, System Message/Error, Software Version, Hostlog Recording, Hostile Event Recording, & Status Spinner.
Define Unit Linkage Table (ULT)!
Enables operator to define the command reporting relationships between subsystems in LAN, EPLRS, or SINCGARS enabled networks. ULT impacts Air Track dissemination and air picture formation, flow or track data through the network, and sets up the command structure between subsystems.