Safety
Saw Safety
Tool Identification
Framing Identification
Materials
Fasteners
Layout
Misc.
100
What must always be worn when working on the site? (Three things)
Safety glasses, hard hat, close toed shoes
100
The type of cut allowed on the miter saw is a:
cross-cut
100
Level
100
These are measured to 92-5/8"
stud
100
What is the size of a 2x4
1-1/2 x 3-1/2
100
What type of screw head is this?
Phillips head
100
What does a “T” represent?
Trimmer
100
What was the size of the plywood sheet that was provided to you?
4x8
200
For safety, wear __________________ when lifting heavy and sharp materials.
gloves
200
What is kickback?
a dangerous occurrence of the tool or workpiece moving back toward the user at high speeds.
200
Speed square
200
What is responsible for providing a base for the window to rest on?
sill
200
What does the "PT" in PT Lumber stand for?
Pressure Treated
200
What is the typical length of a 16d nail?
3-1/2"
200
Where should a stud be placed on the markings?
The stud should be on the side of the line with the X
The edge of the stud should line up with the line marked
200
What did we use to cut out the cup for the ball to fall into?
Hole saw
300
When cutting a board, where should the saw blade be in relation to the measured and marked line?
Immediately on the waste side of the line
300
When using a circular saw, what tool can be used to help you cut straight through the workpiece by pushing it up against the board's edge?
Speed square
300
Flat/Pry bar
300
A vertical member that runs from the sole plate up to the underside of the Header. Its job is to support the ends of the Header.
trimmer
300
What is the size of a 1x8
3/4 x 7-1/4
300
What tape measure fraction is closest to an 8d nail's typical thickness?
1/8"
300
What does an “⭙” (X with a circle around it) represent?
Cripple
300
What did we use to remove nails for the original demolition
catspaw
400
You need to wear a harness on scaffolds that are over ______ high.
6'
400
Cutting a long board, with a circular saw, that is between two sawhorses has the potential to lead to ___________ the blade.
pinching
400
Provide both names for the following:
Reciprocating saw
Sawzall
400
Short vertical studs placed above a Header (supporting the top plate) or below a window Sill (supporting the sill). They fill the space and provide a nailing surface.
cripple
400
What is the size of a 2x10
1-1/2 x 9-1/4
400
Nail sizes are based on what system?
Penny - cost of a 100 nails is used to describe nail size
400
To create 16" O.C. stud spacing, where should the first line off the edge of the plates be drawn for stud placement?
15 1/4"
400
Laying a sheet of plywood on an existing frame is referred to as:
Sheathing
500
When using an extension ladder, how do you test that it is set up correctly? (Three things)
Lean the ladder against the wall approximately at a 4:1 ratio (for every 4ft up, place the base 1ft back )
Make sure the base of the ladder is on even ground
Stand on the bottom rung and do a lean test
500
What can cause kickback? Give me three examples.
changing the direction (or twisting the blade) in the middle of a cut
twisting the workpiece (wood) against the blade during the cut
allowing the blade to touch the workpiece (wood) before it reaches its full speed
500
Chalk line
500
This is at the very very top of the wall assembly from the study guide. (Highest board)
Double top plate
500
What is the actual size of a 8x8 post
7-1/4 x 7-1/4
500
What type of screw head is this?
Torx
500
A 2x6 header assembly would be how wide?
7"
500
When did, the GOAT, Larry Haun pass away?
2011