ENERGY
Select the type of energy that can cause harm or injury. Select all that apply.
A.Pneumatic
B.Mental
C.Hydraulic
D.Electrical
E.Mechanical
A.Pneumatic
C.Hydraulic
D.Electrical
E.Mechanical
Tags must be ________ attached to the energy isolation device.
A.seldom
B.securely
C.never
D.lightly
B.securely
Who must be notified that lockout or tagout devices have been removed prior to release of equipment?
A.Security
B.Loss prevention
C.All affected employees
D.All non essential employees
C.All affected employees
What are the four primary steps for Lockout/tagout?
A.Lock, tag, clear, try
B.Lock, clear, try, reset
C.Look, reset, clear, remove
D.Remove, look, check, test
A.Lock, tag, clear, try
What is the circumference of the Earth in kms?
40074.28 KM
What statement best describe stored energy?
A.Energy associated with a moving vehicle
B.Energy associated with motion
C.Spring under tension
D.Energy of motion used to perform work
C.Spring under tension
Lockout/tagout prevents incidents by _____________ power and energy before machine repair, cleaning, or maintenance.
A.pulling on
B.shutting off
C.turning on
D.switching on
B.shutting off
Who is responsible for the lockout of machine or equipment?
A.Other employee
B.Security
C.Visitors
D.Authorized employee
D.Authorized employee
After Isolation of the equipment what steps needs to be done?
A.Start the work because it is already safe
B.Remove equipment from the power source
C.Isolate all devices
D.Remove and dissipate all stored energy
D.Remove and dissipate all stored energy
How many moons does Jupiter have?
79
Select the sources of stored energy.
A. Electrical, hydraulic, locking and tagging
B. Steam, pneumatic, pits, vessels
C. Hydraulic, pneumatic, spring under tension
D. Tanks, pits, skirts, valves
C. Hydraulic, pneumatic, spring under tension
What should you do if the tag is illegible?
A.Write something to make it readable
B.Just continue and finish the job
C.Immediately report to supervisor
D.Immediately remove the Tag
C.Immediately report to supervisor
Before lockout or tagout devices are removed and energy restored, what should the authorized employee do?
A.Ensure that all employees and contractors remain in the area where the equipment is being reenergized.
B.Install Lock and Tags on all equipment.
C.Install energy-isolating devices on all equipment.
D.Ensure that all employees and contractors are removed from the area or are at a safe distance from the equipment that is being reenergized.
D.Ensure that all employees and contractors are removed from the area or are at a safe distance from the equipment that is being reenergized.
Which of the following are the two(2) key elements for isolation?
A.(1) Test for the toxic gas (2) install any tag
B.(1) energize the equipment (2) communicate with affected personnel
C.(1) energize the equipment (2) test for proper isolation
D.(1) identify what needs to be isolated (2) communicate with the affected personnel
D.(1) identify what needs to be isolated (2) communicate with the affected personnel
What is the depth of the deepest part of the ocean in meters?
8380 meters
Which of the following is a type of energy that can cause injury to personnel?
A.Welding
B.Chisels
C.Electric Power
D.Sea Water
C.Electric Power
An _______________ is one whose job requires the operation or use of machine or equipment on which servicing and maintenance is performed.
A.Authorized employee
B.Other employee
C.Affected employee
D.Contractors
C.Affected employee
Who is responsible to ensure that the service work is complete and the area is restored before re-energizing?
A.Workers
B.Work Permit Reciever
C.Operations
D.Maintenance Supervisor
C.Operations
Select and place in a correct order the 3 key elements of an energy control program from the list .
A.Periodic inspection, training, specific written procedures
B.Specific written procedures, training, periodic inspection
C.Training, periodic inspection, specific written procedures
Periodic inspection, specific written procedures, trainin
B.Specific written procedures, training, periodic inspection
How high is the Burj Khalifa in meters?
828m
Energy in motion is also called __________________.
A.Wind energy
B.Solar energy
C.Kinetic energy
D.Cosmetic energy
C.Kinetic energy
Lock must have their own unique?
A.Number
B.Color
C.Key
D.Identity
C.Key
After placing his lock and hold tag on the main breaker, what must the issuer do before issuing the permit?
A.Authorize the start of work
B.Try to start the equipment at the local switch to ensure the lock is applied properly
C.Make sure gas tests are done
D.Notify his supervisor
B.Try to start the equipment at the local switch to ensure the lock is applied properly
In lock out/tag out, you must _________ what needs to be isolated or controlled.
A.Remove
B.Recover
C.Close
D.Identify
D.Identify
According to Wikipedia, how many goals has Cristiano Ronaldo scored in his career?
954