M821
When a tool reconditioning is complete the tool should be at what percent?
If a base body is damaged and needs manufactured what percent is the tool set to?
80%
40% to 59%
What does AFD stand for?
What about XGP?
Axial Flaw Detection
Extended Geometry Pig
Another name for a tool run simulation is:
Dry Test
Offline Mode Test
End Test
CD stands for what?
What about WT?
Crack Detection
Wall Thickness
What are the 3 types of cup shore?
65,75 and 85.
When must brushes be replaced?
When must an EMAT carrier lid be replaced?
When one indicator is missing.
When 4 tungsten balls are missing.
What does ATEX stand for?
What is the ITX tester called?
Atmosphere Explosive
EPD- Electronic Pig Detector.
What is the sample interval for an ECD?
What about for a UCD?
5.0mm
2.0mm
When should a UCD slider be replaced?
When the slider is completely wore down past the radius.
How many runs can LVDS cables go on?
Where can I find what run they are on? OneNote is not a correct answer.
3
Statistics
What is a primary battery?
What is a secondary battery?
A non-rechargeable battery.
A rechargeable battery.
Setting yoke stop height can be extremely important. At what installations does this matter?
Launcher oversize
Tees
Y-pieces
Name a physical item that is required for an EMAT Online Sensor Test.
How can one stimulate the Hall Sensors?
A sensor test plate or a magnet bar.
With a magnet or odometer axle.
What shall be done with sensor cables after the first run if they are able to be reused?
Cut one small edge on each cable connector.
What must be checked when installing UCD carrier angles on a UCD.
The angle and size "inch value" or part number.
What does the DPT sensor do?
How could one test this?
Explain the relationship between the "P" and the "T"
It measures atmosphere pressure and temperature.
By using the cold spray on it.
As Temperature rises pressure will also rise. As temperature drops, pressure will also drop.
What must be documented in the PU section of the TPR? Be detailed.
All PU, ring brushes and spacers must be documented and include details such as bypass holes or notches.
What is the standard standby time delay time for ECD and UCD tools?
What about for a PDIA tool?
What about for a tool with a Gyro?
7200s
1000s
0s
What happens with sensors after they are run?
They are cleaned and sent back to Lingen for refurbishment and testing.
What is the function of a pressure switch?
The pressure switch is a safety mechanism that turns the tool on via pressure after safely being loaded in the pipe. This ensures the FIO Tech. does not have to flip a physical switch in an explosive environment.
What are some things that could disqualify an ASC valve for service? Name at least 4.
Fatigue cracking
Debris
Clearance between the valve (Gap)
Bent Parts or abrasion
The valve is not opening or closing all the way.
The valve is pulling excessive current. (Amps)
What does a PDL measure? Is there a type of tool you know of that might run one?
Temperature, pressure, differential pressure and acceleration.
Cleaning tools.
What types of cracks do UCD tools measure?
What about a UTD?
What about a UWD?
Axial cracks or flaws.
Circumferential cracks or flaws.
Wall thickness values and corrosion.
A UT-A is what kind of tool? What direction do carriers face?
A UT-C is what kind of tool? What direction do carriers face?
UTD- Upstream and downstream
UCD- Clockwise and counterclockwise
What are some things that might disqualify a EMAT sensor for use? Name at least 3.
A cracked sensors
Blackened pins
Pins of different lengths
Delamination of the sensor
Oil leaking from the sensor.
Sensor coil or wires are visible