LOTO
PPE
ENVIRONMENTAL
GENERAL SAFETY
MACHINE GUARDING
100

True or False. LOTO devices must be labeled to identify the specific employees authorized to apply & remove them. 

What is True... Each "authorized employee" must have their own lock and key that is to be used by them and them alone. 

100

What is the "E" in PPE

What is the Equipment?

100

True or False. There is a difference between STORM water sewers and WASTE water sewers.

What is True. ONLY RAINWATER can to into Storm Sewers. 

100

Where go i go when evacuating the building during a Fire Drill?

What is the facility rally point station

100

True or False. Its ok to remove a guard if its broken or not functioning correctly. 

What is false... You never remove a broken or malfunctioning guard on a piece of equipment. you report it to your supervisor so it can be repaired. 

200

True or False. “Affected employees” are those responsible for implementing the energy-control procedures or performing the service or maintenance activities. 

What is False. only "Authorized employees" that have been trained and performed an audit of proficiency are certified to lock out equipment. 

200

Sunglasses can be used in place of required safety glasses.

TRUE or FALSE

What is FALSE 

200

There is a designated area for recycling batteries?

What is TRUE. there is a bucket marked Universal Waste for all different types of batteries (A, AA, AAA.... etc.).

200

The acronym  "OSHA" stand for

What is the Occupational Safety & Health Administration?

200

True or False. Any machine part, function or process which may cause injury must be safeguarded 

What is true... 

300

When conducting a lockout operation, electricity is the only energy source you should consider.

What is false. All energy sources must be isolated in order to achieve correct lockout of the equipment. 

300

Personal Protective Equipment is required when

Engineering, work practice, and administrative controls do not provide sufficient protection against hazards

300

True or False is ok to immediately clean up a chemical spill you see in the plant.

What is False... DO NOT clean up a spill if It’s too big, You cannot identify the chemical, and you don’t have proper PPE. instead report the spill immediately to your supervisor. 

300

Who should you contact if you get hurt?

What is your supervisor.

300

Interlocks can be defined as

What is... They are used to shut off power, control personnel access and prevent a machine from starting when the guard is open.

400

During a lockout procedure, one person can attach a single lock for an entire work crew.

What is false... All "Authorized" employees must have their locks on the equipment before work is to begin on it. 
400

True or False. Sharps punctures from improper PPE are one of the most common methods of transmission by BBP in the workplace.

What is True

400

What does SDS stand for

What is Safety Data Sheet

400

Name two things you can do to prevent a job injury.

What is... Report unsafe conditions, get safety training, follow safety rules, refuse to do something that is too dangerous, ask questions if you don’t understand

400

True or False. Operators should receive training on how and why to use safeguards and how and when safeguards can be removed and by whom.

What is true...

500

True or False. The correct time to use LOTO is whenever you are performing service or maintenance on any piece of machinery or equipment where you could be injured by unexpected startup or release of stored energy

What is True. 

500

True or False. If you wear prescription lenses, you do not need additional eye protection against occupational eye hazards.

What is false. prescriptions lenses must be constructed of impact resistant material that meets ANSI Z87.1 construction with permanent side shields. 

500

True or False. A container of unidentified chemical, should be dumped in the hazardous waste satellite collection drum.

What is false...The chemical should be set aside and labeled as “Analysis Pending” until it can be properly identified

500

What are two things you should do if you get hurt on the job?

What is...Tell your supervisor and get out of a dangerous area.

500

Installing a machine in a place where no one can contact moving parts is an example of

What is guarding by location