MPM-11-052 Method to Clean SS Screws and Hardware
MPM-11-060 Manufacturing Instructions for MPM and WI
MPM-11-060 Manufacturing Instructions for MPM and WI Part 2
MPM-11-066 Epoxy, Solder Paste, etc. Materials Handling and Curing Procedure
MPM-11-066 Epoxy, Solder Paste, etc. Materials Handling and Curing Procedure Part 2
100

What is the minimum time that the hardware should be ultrasonically cleaned?

a. 15 min

b. 20 min

c. 30 min

d. 1 hour

a. 15 min

100

What does WI stand for?

Work Instructions

100

What does MPM stand for?

Manufacturing Process Methods

100

Shelf Life will be listed on the material’s _______ Shelf Life label

a. Red

b. Yellow

c. Green

d. White

c. Green

100

True or False: The oven door shall be opened anytime once the curing cycle has started.


False. The oven door shall not be opened once the curing cycle has started.

200

What should be the exact level of acetone filled in the beaker (in relation to the hardware)?

a. Approximately ½” below the hardware

b. Approximately ½”

c. Approximately ½” above the hardware

d. No measurement. how much we want

c. Approximately ½” above the hardware

200

_______ are general procedures written for either program-specific information, facility process requirements, and/or equipment operating procedures.

a. Command Media

b. MPM

c. WI

d. Drawing

b. MPM

200

_______ are specific procedures written for a specific part number typically with engineering parts list

a. MPS

b. MPM

c. WI

d. Drawing

c. WI

200

When different materials are to be cured in a single oven, the timer shall be set to the _______.

a. Average time

b. Sum time

c. Shortest time

d. Longest time

d. Longest time

200

The bin is emptied, operations personnel shall deliver the empty bin to _______

The area PP&C representative

300

Inspect the hardware for FOD using _______ magnification

a. 10X

b. 50X

c. 20X

d. 100X

a. 10X

300

MPM and WI are _______ and shall be marked appropriately.

a. LOCKHEED MARTIN PROPRIETARY INFORMATION

b. CLASSIFIED

c. CONFIDENTIAL

d. SECRET

a. LOCKHEED MARTIN PROPRIETARY INFORMATION

300

True or False: WI are procedures written for a specific Part Number. 


True

300

_______ is the general term used to describe the time a material must be used once it has been mixed or, been thawed out

a. Expired Time

b. Pot Life

c. Shelf Life

b. Pot Life

300

PN AD-MC-0854-01 (individual packages), PN AD-MC-0854-03 (tubes of epoxy), Allow epoxy to _______ before handling.

a. Air dry for 5 minutes

b. Oven cure for 5 minutes

c. Air dry for 15 minutes

d. Oven cure for 15 minutes

c. Air dry for 15 minutes

400

After cleaning the screws or hardware, write on the bag or label, “Cleaned by _______ and _______”.

Cleaned by employee # and the date

400

List 6 out of 9 sections that WI must include in the documentation.

  • Title Page
  • Table of Contents
  • Reference Documents
  • Tool and Material List
  • Acronyms
  • Environmental, Safety and Health
  • Precautions and General Notes
  • Operations
  • Change History
400

True or False: In the WI, "Change History" is located after the table of contents.

False. In the WI, "Change History" is located on the very last page.

400

Before use, allow the material to thaw for a minimum of _______ for manual use and _______ for automatic dispenser use.

5 minutes for manual use

15 minutes for automatic dispenser use

400

Automatic Dispenser Use – Set the syringes to stand _______ while thawing.

a. Vertically

b. Horizontally

a. Vertically

500

What specific MPM should be followed when preparing the table top ultrasonic cleaner for use?

a. MPM-11-052-CHM

b. MPM-11-060-CHM

c. MPM-11-066-CHM

d. MPM-11-074-CHM

d. MPM-11-074-CHM Use of Ultrasonic Tabletop Cleaner

500

Work Instructions during Development (prior to Production). List 2 Engineering Development Suffixes.

  • +PP or :PP  (Pre-Production Assemblies)
  • +BB or :BB (Brass Board Assemblies)
  • +Qual or :Qual (typically +PP or :PP Assemblies designated for Qualification)
  • +EU or :EU (Engineering Use Only Assemblies)
500

List 3 out of 5 sections that MPM must include in the documentation.

  • Scope
  • References/applicable documents
  • Environmental, Safety and Health
  • MATERIALS/EQUIPMENT
  • PROCEDURE
500

Any material lot found to be within _______ of its expiration, shall be removed from the production floor and replaced with a newer lot from the stockroom.

a. 7 days

b. 5 days

c. 2 days

d. Same day

a. 7 days

500

_______ personnel are responsible for the proper labeling of the shelf life and storage materials

a. Quality Receiving/Inspection

b. Stockroom

c. PP&C

a. Quality Receiving/Inspection