Paints / Chemicals
Tools / Equipment
Personal Protective Equipment
Wood Working Safety
Fire Extinguisher Safety
100
Where should combustible liquids be stored?
a. In a closed plastic container.
b. On a open storage shelf.
c. In a closed metal container.
d. Outside of the building in a storage unit.
c. In a closed metal container.
100
No one should use any shop equipment until:
a. They have seen someone use it.
b. They have read the owner's manual.
c. They have been trained to operate it.
d. They have watched the training video.
c. They have been trained to operate it.
100
Which of the following is the most correct?
Safety glasses should be worn:
a. Only, when working on the table saw.
b. Only, by those working with and around the table saw.
c. Only when using the grinder.
d. When there is any risk of eye injury from flying particles, chemicals, or other hazards.
d. When there is any risk of eye injury from flying particles, chemicals, or other hazards.
100
Sliding Miter Saw:
- YOUR FINGERS AND THE PATH OF THE BLADE SHOULD NOT COME CLOSER THAN
- 4”
- 6”
- 8”
- 10”
6 Inches
100
When using an fire extinguisher to put out a fire, you should:
a. Stand back about six to ten feet.
b. Aim at the base of the fire.
c. Spray with a side to side motion.
d. All of the above.
d. All of the above.
200
Discussion Scenario:
Explain how you would keep students safe using chemicals / Paints which potentially can lead to respiratory issues," or "lung disorders?
Answers can vary according to the discussion.
Do you have access to any N 95 rated Respirator Masks?
200
True of False
My power cord on my grinder is to short and doesn't reach the outlet. Can I use an extension cord attached to my surge protector?
False
Tools and equipment needs to be plugged in directly to the outlet.
Consult with the amp rating of the equipment your working on.
No Daisy Chaining.
200
How often should you test an eye wash station?
Weekly. Rust can accumulate and if not cycled when needed can get into your eyes.
200
TABLE SAW
1. DO NOT RIP LUMBER WHEN THE FENCE AND BLADE ARE CLOSER THAN
a. 3/4”
b. 1”
c. 1 1/4”
d. 1 1/2”
d. 1 1/2”
200
What are the Letters associated with fire extinguisher types?
A,B,C,D,K
300
Generally speaking which two types of water based paints are not flammable?
latex and acrylic paints
300
Discussion Scenario:
You are getting ready for this nights performance. Johnny is cutting some wood on the table saw. The head secretary just called over the intercom for you to report to the office a parent is waiting. Discuss what you would do.
1. Have Johnny stop cutting wood on the table saw.
2. Disconnect Power to table saw.
3. Remove Johnny from shop area and lock the door.
Who is responsible for Johnny, if he gets hurt?
Can someone else watch Johnny to make sure he is safe?
300
What does SDS stand for?
Safety Data Sheets
300
Table Saw:
1. DO NOT RIP BOARDS THAT ARE LESS THAN
a. 6” LONG.
b. 8” LONG.
c. 10” LONG.
d. 12” LONG.
2. USE A PUSH STICK WHEN THE FENCE AND THE BLADE ARE CLOSER THAN
a. 4”
b. 6”
c. 8”
d. 10”
3. THE BLADE SHOULD BE SET ABOVE THE WOOD BEING CUT
a. 1/16” TO 1/8”
b. 1/8” TO 1/4”
c. 1/4” TO 1/2”
d. 1/2” TO 3/4”
Answer #1 C 10"
Answer #2 B 6"
Answer #3 C 1/4" to 1/2"
300
According to fire extinguisher safety what does the acronym PASS stand for
PASS - Pull, Aim, Squeeze, Sweep
400
OSHA 1926.152 stipulates that “no more than ____ gallons of flammable liquids shall be stored in any one storage cabinet.
60 Gallons
More than 60 gallons require a storage unit separate from the facility according to OSHA 1926.152.
400
Discussion Scenario:
1. Who is responsible to inspect and service equipment?
2. Do you have a checklist?
3. What do you do with equipment or tools that isn't functioning Properly?
400
When building stage sets when should gloves be used?
Answers may vary.
Gloves should Not be used anytime you are cutting wood.
400
BAND SAW
1. THE UPPER GUIDE ASSEMBLY SHOULD BE ADJUSTED ABOVE THE WOOD BEING CUT
a. 1/16” TO 1/8”
b. 1/8” TO ¼”
c. ¼” TO 5/16”
d. ¼” TO 3/8”
2. WHEN SAWING SHARP CURVES, DO THE FOLLOWING EXCEPT
a. PUSH AND TURN THE WOOD SIMULTANEOUSLY (AT THE SAME TIME).
b. MAKE RELIEF CUTS
c. USE A MITER GAUGE
d. FEED THE WORK MORE SLOWLY.
3. ON THE BAND SAW, NEVER ALLOW YOUR FINGERS AND THE PATH OF THE BLADE TO COME CLOSER THAN
a. 1”
b. 2”
c. 3”
d. 4”
Answer #1 D ¼” TO 3/8”
Answer #2 C USE A MITER GAUGE
Answer #3 B 2”
400
How often do fire extinguishers need to be inspected?
At least once a month, and a professional maintenance inspection should be done annually.
500
Discussion Scenario:
If I need to dispose of some used paints or chemicals what do I do?
Step 1: Notify Head Custodian
Step 2: The custodian will then arrange a disposal method through Districts Risk Management.
500
Discussion Scenario:
Johnny's father is a license contractor and builds homes for a living. Johnny spends time working on building homes with his father during the summer and holiday breaks. Johnny has asked to use the equipment in the stage tech class during your day off with the substitute teacher. Your substitute teacher is a licensed contractor.
Substitute teacher Discussion.
1. Is Substitute teacher certified to teach?
2. Substitute might not be familiar with equipment being used.
500
Name at least 5 types of (PPE) Person Protective Equipment.
Does your students have access to any of the above PPE.
500
Discussion Scenario:
1. What safety practices and procedures are you using making sure the students are properly trained and certified?
2. How long do you keep safety certifications on file after the student has graduated?
1. Demonstration on Equipment.
2. Safety Test.
3. Equipment Certification.
4. Standards based grading rubrics / evaluations.
5. CTE requires teachers to hold onto safety tests or certifications until the student reaches the age of 21.
500
Who should you contact when you need a Fire Extinguisher Serviced?
Your Schools Head Custodian.
