MPM-11-052 Method to Clean SS Screws and Hardware
What is the minimum time that the hardware should be ultrasonically cleaned?
a. 15 min
b. 20 min
c. 30 min
d. 1 hour
a. 15 min
What does WI stand for?
Work Instructions
What does MPM stand for?
Manufacturing Process Methods
Shelf Life will be listed on the material’s _______ Shelf Life label
a. Red
b. Yellow
c. Green
d. White
c. Green
True or False: The oven door shall be opened anytime once the curing cycle has started.
False. The oven door shall not be opened once the curing cycle has started.
What should be the exact level of acetone filled in the beaker (in relation to the hardware)?
a. Approximately ½” below the hardware
b. Approximately ½”
c. Approximately ½” above the hardware
d. No measurement. how much we want
c. Approximately ½” above the hardware
_______ are general procedures written for either program-specific information, facility process requirements, and/or equipment operating procedures.
a. Command Media
b. MPM
c. WI
d. Drawing
b. MPM
_______ are specific procedures written for a specific part number typically with engineering parts list
a. MPS
b. MPM
c. WI
d. Drawing
c. WI
When different materials are to be cured in a single oven, the timer shall be set to the _______.
a. Average time
b. Sum time
c. Shortest time
d. Longest time
d. Longest time
The bin is emptied, operations personnel shall deliver the empty bin to _______
The area PP&C representative
Inspect the hardware for FOD using _______ magnification
a. 10X
b. 50X
c. 20X
d. 100X
a. 10X
MPM and WI are _______ and shall be marked appropriately.
a. LOCKHEED MARTIN PROPRIETARY INFORMATION
b. CLASSIFIED
c. CONFIDENTIAL
d. SECRET
a. LOCKHEED MARTIN PROPRIETARY INFORMATION
True or False: WI are procedures written for a specific Part Number.
True
_______ is the general term used to describe the time a material must be used once it has been mixed or, been thawed out
a. Expired Time
b. Pot Life
c. Shelf Life
b. Pot Life
PN AD-MC-0854-01 (individual packages), PN AD-MC-0854-03 (tubes of epoxy), Allow epoxy to _______ before handling.
a. Air dry for 5 minutes
b. Oven cure for 5 minutes
c. Air dry for 15 minutes
d. Oven cure for 15 minutes
c. Air dry for 15 minutes
After cleaning the screws or hardware, write on the bag or label, “Cleaned by _______ and _______”.
Cleaned by employee # and the date
List 6 out of 9 sections that WI must include in the documentation.
True or False: In the WI, "Change History" is located after the table of contents.
False. In the WI, "Change History" is located on the very last page.
Before use, allow the material to thaw for a minimum of _______ for manual use and _______ for automatic dispenser use.
5 minutes for manual use
15 minutes for automatic dispenser use
Automatic Dispenser Use – Set the syringes to stand _______ while thawing.
a. Vertically
b. Horizontally
a. Vertically
What specific MPM should be followed when preparing the table top ultrasonic cleaner for use?
a. MPM-11-052-CHM
b. MPM-11-060-CHM
c. MPM-11-066-CHM
d. MPM-11-074-CHM
d. MPM-11-074-CHM Use of Ultrasonic Tabletop Cleaner
Work Instructions during Development (prior to Production). List 2 Engineering Development Suffixes.
List 3 out of 5 sections that MPM must include in the documentation.
Any material lot found to be within _______ of its expiration, shall be removed from the production floor and replaced with a newer lot from the stockroom.
a. 7 days
b. 5 days
c. 2 days
d. Same day
a. 7 days
_______ personnel are responsible for the proper labeling of the shelf life and storage materials
a. Quality Receiving/Inspection
b. Stockroom
c. PP&C
a. Quality Receiving/Inspection