How many wishes do you normally get from a genie?
None!!!!!!, it is a Powered Personnel lift that is not something you should joke around with... In order to use the genie you must first be genie certified, the test is pretty easy tbh you got it.
What is a Chuck?
Is Chuck the part of the drill where you put the bit? Yes Obviously >:{
If your long hair or dangling jewelry is really cool can you keep it like that while operating tools?
No.
Which type of saw can you wear gloves with?
What is none of them?
If you staple you friends hand, what should you do?
Apologize you meanie, but also be careful so like that doesn't happen? Bur for real though immediately inform an adult supervisor.
What are the five things you should do before coming to school?
hahaha jk, the real question is what tools require using safety goggles? tomas knows the answer.
Which type of bit do we normally use?
I think it's star bit, but I'm new here so it could be something else. ps tomas told me its a star bit!
Which step in the checklist is the least important
WRONG, they're all super important so do all of it every time. -9000 points if you named one of these steps: Long Hair must be pulled back. Check for missing or damaged parts. Ensure the casing is not cracked. Check that handles are secure. Ensure electrical cords and plugs are in good condition (no damage to insulation, exposed internal wires, taped wires, or missing ground pins). Make sure all guards are present and working properly. NEVER wear gloves when using any of these tools. Make sure that all bits, belts, and blades are straight and tightly clamped. Disconnect power or remove battery from the tool before reloading or adjusting bits or blades. Remove all adjusting keys and wrenches prior to starting a tool. If a tool is dropped while work is in progress, reinspect prior to continuing operation.
How far should your fingers be from the blade when operating a miter saw?
6 inches,
Follow the rules.
Who do we use when we want to make a piece of wood smoother or take like a little bit off without using a saw?
the electric sanders, you've gotta wear goggles when handling him, and complete the general inspection prior to use.
what is wrong with Ronny's usual fit
Although he is super dripped out, he cannot wear crocks in a work environment.
If you drop your drill while it is in use, what do you do next?
Well first I would probably say "dang it" and then maybe I'd be like "guys sorry I dropped it I didn't mean to" and then I would go pick it up, and if there is anyone watching me I would do the whole inspection again which includes, While powered off, check for missing or broken parts. Check the tool casing for any cracks. Check that torque is properly set for the bit. Make sure workpiece is properly secured. Insert and tightly secure the bit in the chuck.
But that's just what I'd do IDK about you.
If a handle is not secure, should you use the tool?
What is no?
What saw is the most dangerous?
Jigsaw... hahaha just kidding. All saws are equally dangerous so be VERY careful plz :)
when should ear protection be worn
when my apple watch tells me there is a loud environment warning. JK you actually do it when you're using all power tools, so either one, better safe than sorry tho
When do you apply pressure when using a drill/impact driver?
When you are doing forward or reverse use? Yes.
When operating a drill or impact driver, what are the six things you need to make sure to do. If you don't do them you will get fired?
What is maintain proper grip on the drill or driver?What is maintain moderate and even pressure?
What is maintain appropriate tool speed?
What is demonstrate correct forwards use?
What is demonstrate correct reverse use?
What is reduce speed to prevent seizing when the bit is about to break through the material?
If a tool is connected to a power source?
What?
List the proper inspection, preparation and operation protocol for panel saw, this is closed notes, you have 3.4 minutes? spelling does not count >:)
While powered off, check for missing or broken parts; inspect the blade, Check the tool casing for any cracks, Check that all handles are secure, Make sure all guards are present and secure, Inspect the dust collection system, making sure it is properly attached and in good.
rip cut - Place workpiece on lower support track/rollers and, with the saw in the upper rest position, verify smooth side to side travel of the workpiece throughout the full length, Ensure the blade is locked in rip cut (horizontal) orientation, Position the saw and lock at correct ripping height using the mounted vertical rip measuring tape, Confirm ripping direction and position workpiece on the correct side of the saw, Ensure blade is rotating at full speed before feeding the workpiece into the sawblade, Coordinate with receiving technician to smoothly feed material through the saw at a constant speed, Ensure the blade has fully stopped before adjusting carriage.
cross cut - Ensure blade is locked in cross cut (vertical) orientation, Carefully release carriage lock and move saw vertically on the guide tubes through full range of crosscut travel to ensure freedom of movement; return saw to uppermost crosscut position, Place workpiece so that it is supported by a minimum of 2 material rollers, Ensure blade is rotating at full speed before cutting, With a firm grip, slowly bring saw down at a constant speed, cutting in a smooth downward motion until saw passes through material, Ensure blade has come to a complete stop before returning carriage to the starting position, Remove material from both sides of saw.
How long are you allowed to leave an extension cord plugged in?
30 days before it blows up the entire school
What are the four types of ladders students are allowed to use?
A-Frame, Platform, Step Stool, Twin?
What screwdriver is best used in cold weather?
Who is Philip?
how often do you have to generally inspect your tools?
every time tomas asks you to? NO, every time you begin using a tool or like drop it or something.
List the proper operation protocol for miter saws, must be in order, spelling counts, you have 30 seconds.
what is Miter - hold wood flat against the table and firmly against the fence, Keep non-cutting hand at least 6 inches away from the blade, Ensure blade is rotating at full speed before lowering it to cut, Ensure blade has stopped fully before raising and returning it to the starting position?
What is the minimum #number of people necessary to operate the panel saw; effectively?
2?