Safety Jeopardy Games

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

The steps to extinguisher fire are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

The steps to extinguisher fire are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

When a straight or extension ladder is used to climb onto or off an upper surface, it must be extended  _____ ft. beyond that surface.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

The steps to extinguisher fire are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

The steps to extinguisher fire are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

The steps to extinguisher fire are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

Passageways on construction sites must have a clearance of ______

Fire extinguishers are required every ________ sqft, and no more than ________  feet travel distance. 

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

____________________controls is a method of rotating employee in and out of an area the limit the exposure levels.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

______________ is not allowed on any construction site and immediate dismissal from the site is required if found.

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

__________ must be obtained from the Safety Representative Prior to Operations and submitted at the when operations finish.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

It is prohibited for portable space heaters to be use at construction site for human comfort.

True or False

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

License to used for torch operators. 

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class E hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required at 

The steps to use a fire extinguisher are 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

The initial hydro static test must be done at _________.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

The OSH Act was passed into law in the year.

The first method on the hierarchy of controls is ___________.

A straight ladder must extended _______ feet above the landing.

Mushroom caps are an acceptable form of protection from rebar impalement. 

True or False

I can hang the temporary lightening by placing metal screws in sheet rock and place the stringer on the screw. 

True or False

A light weight scaffold can withstand _____PSI.

When Assembling and disassembling a crane an _____________ director must supervise the operation. 

SOE are needed when the depth is more than _____ ft. 

It is best practice to use a ________ instead of a ladder when working at height above six feet.

If there is a hazard at a workplace, but there is no specific OSHA standard covering this hazard, OSHA can still cite and fine an employer for that hazard. 

__________ is the last resort when trying to control a hazard.

A double ladder is required when there are ________ or more workers. 

The acceptable oxygen level is between _____________.

Temporary walkways shall have a ________ amount of clearance. 

Scaffold _______________ must be fully attached and may be used as a midrail.

A Licensed Rigger or Registered Design Professional is Required always is required for __________ operations. 

______________ can not be more than 3 stories below the working deck. 

Toe board height is 

Section 5a of the OSH Act of 1970 is called the ......

Fall protection must be used any time a worker is with in ______ feet from an elevated surface.

Handrails are needed on stairwells when there are ___ or more risers.

Every ___________ feet after the initial hydro static test an repeat test must take place.

The CDA is located __________.

Viewing Panels on a fence must be every ___________ft. 

____________ must be used to guide the load. 

Reshored must be secured within __ft from the edge of the building?

Top rails must withstand ___ pounds of downward and outward force?

The general duty clause says that employers must furnish a ________________________________________.

A ___________ must be in place prior to removing protection. 

The ____________ must be opened and locked on a step ladder.

Methane can not exceed _____ percentage of the LEL.

A fence is required at a construction and demolition site ______________. 

A designed scaffold has to be inspected by an engineer  when it ____________, __________, and __________.

Crane operations must stop when wind speed reaches 

Outrigger scaffolds need a certain form. 

Scaffolds must be have a height to base ratio of _____.

What is OSHA’s highest inspection priority?

A body belt is a form of fall protection.

True or False 

Handrails must be free of ___________.

Compressed gases are considered in storage when the regulator removed and ____________ are placed on.

Horizontal netting shall be projected outwards ______.

Erector and dismantlement holds a _____ training certification.

An assist crane.

All sites must have a _____________ Plan.

Cranes must stay away from power lines a certain distance. 

The five categories of citations penalties are ....

Class G hardhats can resist 2,200 volts of electricity.

True or False

Stair pans must have ________ material before they are used to avoid tripping hazards. 

Three elements that cause a fire are ____________.

Horizontal netting is required  at ________ stories. 

A ____________ must be attached to the lifeline while working on a suspended scaffold.

Safety coordination meeting is used for __________  crane. 

Best squad stands for ______________.

A__________ is required when the building is 20 stories or more in height. 

A willful violation cost approximately ____________. 

Prior to wearing a respirator a worker must have __________.

Staircase landings must have a __________ around the open edge. 

___________ are the number one hazard of excavation. 

A ________ and __________must be in place and readily accessible at all times when the building reaches 75 feet for the FDNY.

A ________________ report must be on file before the scaffold can be used. 

All cranes and derricks must be equipped with an __________. 

Before excavation, you must notify the adjoining property __________ feet prior. 

______________ must be in the cabin of the crane. 

At International Paper, we have __________ in the form of rules, policies, checklists and procedures intended to safely conduct work.

We refer to this as the "Black Line" which is _______________.

SDS; 

Where can I find it and when might I need one? 

What are the 3 characteristics that define a Confined Space. 

In a caution or low hazard situation, any ________may erect yellow/black barricade tape to limit access to the area.  

Give one example of a low hazard situation

Any person working within ____ feet of the center of a railroad must attach their ________ ________ to a properly located Blue Flag/De-railer.  

The "Blue Line" represents HOP.  What does this acronym stand for

ALARA 

What does this refer to?

All of the Confined Spaces at Prattville Mill require this.

__________Barricade Tape is used in High Hazard Situations. This barricade tape is to restrict access to only those individuals working with or correcting a hazardous situation.  

Only __________________ working on the hazard(s) are allowed in the area.

In case of an evacuation, where should you report?

Over time, how we actually perform work often drifts away from the ideal “Black Line”.

______  is referred to as the difference between the  “Blue Line” and “Black Line”.  Name at least 3 Examples of where this comes from.

PASS

Name at least 4 members of a CONFINED SPACE ENTRY TEAM

An unprotected roof edge is any roof edge where a person could fall how many feet?

What injury accounts for 35% of all recordables.  

These account for ____% of LIFE impacting injuries.

True or False.

The purpose of safety promotion is to keep employees focused on doing their work the safe way, every day.

True or False.

Employers are not required to have rules that ensure a safe and healthy workplace.

True or False.

Ongoing safety training will promote safety in the workplace.

True or False.

Another way to promote safety through employee involvement is the safety committee.

True or False.

Visual awareness is important in promoting safety within the workplace.

OSH Stands for?

LOTO stands for?

PASS stands for?

HIRAC Stands for?

How many percentage is unsafe act?

How many percentage is unsafe Condition?

Give at least one sample of Physical Hazard.

Give at least one sample of Biological Hazard.

Give at least one sample of Chemical Hazard.

At International Paper, we have __________ in the form of rules, policies, checklists and procedures intended to safely conduct work.

We refer to this as the "Black Line" which is _______________.

SDS; 

Where can I find it and when might I need one? 

What are the 3 characteristics that define a Confined Space. 

In a caution or low hazard situation, any ________may erect yellow/black barricade tape to limit access to the area.  

Give one example of a low hazard situation

Any person working within ____ feet of the center of a railroad must attach their ________ ________ to a properly located Blue Flag/De-railer.  

The "Blue Line" represents HOP.  What does this acronym stand for

ALARA 

What does this refer to?

All of the Confined Spaces at Prattville Mill require this.

__________Barricade Tape is used in High Hazard Situations. This barricade tape is to restrict access to only those individuals working with or correcting a hazardous situation.  

Only __________________ working on the hazard(s) are allowed in the area.

In case of an evacuation, where should you report?

Over time, how we actually perform work often drifts away from the ideal “Black Line”.

______  is referred to as the difference between the  “Blue Line” and “Black Line”.  Name at least 3 Examples of where this comes from.

PASS

Name at least 4 members of a CONFINED SPACE ENTRY TEAM

An unprotected roof edge is any roof edge where a person could fall how many feet?

What injury accounts for 35% of all recordables.  

These account for ____% of LIFE impacting injuries.

2018 had the greatest number of school shooting incidents at __ recorded incidents. 

1. 59

2. 82

3. 74

True or False? A school visitor can enter the building with no questions asked.

True or false? Schools in America are safer than schools in Austria, Iceland and Portugal.

According to IndyStar, what is the biggest reason low-income schools are labeled as “unsafe”?

1. Low-income schools cannot afford new security systems

2. In general, violence is not well-funded in terms of research...There’s no evidence on what works and what does not

3. there are other reasons

True or false?

According to a Florida SB (Senate Bill), people who have been committed to a mental institution are prohibited from possessing a firearm until proven allowed.

When do most school shootings occur?

1. Morning

2. Afternoon

3. Upon dismissal

Emergency communication platforms, are designed to improve the outcome of emergencies through...

1. faster responses 

2. more effective communication between school faculty and staff and first responders

3. keeping everybody safe and informed during emergency situations

4. All of the above

True or false? The Federal Government’s first foray into school safety was the No Child Left Behind (NCLB) act in 1994.

True or False?

One of the biggest reasons high school lockdown procedures fail is lack of communication.

True or false?

There were over 20 school shootings in the past year that resulted in deaths in the United States.

Purpose of the Safety Committee

Chest Compressions

CPR

Compression Rate for CPR chest compressions

Function of the Safety Committee

What is PPE?

Before pressing the shock button on an AED- you should do this

What is SDS? What does it stand for? What is it used for?

Recommended ratio of compressions to breaths in CPR

Goals of the Safety Committee

2 BBPs the Occupational Safety and Health Administration focuses on 

In relation to fire safety, what is RACE?

Phone number for poison control center

2018 had the greatest number of school shooting incidents at __ recorded incidents. 

1. 59

2. 82

3. 74

True or False? A school visitor can enter the building with no questions asked.

True or false? Schools in America are safer than schools in Austria, Iceland and Portugal.

According to IndyStar, what is the biggest reason low-income schools are labeled as “unsafe”?

1. Low-income schools cannot afford new security systems

2. In general, violence is not well-funded in terms of research...There’s no evidence on what works and what does not

3. there are other reasons

True or false?

According to a Florida SB (Senate Bill), people who have been committed to a mental institution are prohibited from possessing a firearm until proven allowed.